Skip to content

BIM Object Library

Revit IFC Bentley Vectorworks ArchiCAD
Wall Ties
Ancon Teplo1 Wall Tie -

2D detail

Low thermal conductivity, basalt-fibre, Type 1 (heavy duty) wall tie for connecting the two leaves of a cavity wall. The material has a thermal conductivity of just 0.7W/mK. Standard tie lengths available.

Tie length is parametrically controlled. The detail includes a moveable heavy duty rubber ‘o’ ring drip and an optional insulation retaining clip.

2D detail
Ancon Teplo2 Wall Tie -

2D detail

Low thermal conductivity, basalt-fibre, Type 2 (general purpose) wall tie for connecting the two leaves of a cavity wall. The material has a thermal conductivity of just 0.7W/mK. Standard tie lengths available.

Tie length is parametrically controlled. The detail includes a moveable heavy duty rubber ‘o’ ring drip and an optional insulation retaining clip.

2D detail
Ancon Teplo4 Wall Tie -

2D detail

Low thermal conductivity, basalt-fibre, Type 4 (light duty) wall tie for connecting the two leaves of a cavity wall. The material has a thermal conductivity of just 0.7W/mK. Standard tie lengths available.

Tie length is parametrically controlled. The detail includes a moveable heavy duty rubber ‘o’ ring drip and an optional insulation retaining clip.

2D detail
Ancon SDB Frame Cramp -

2D detail – plan view

Stainless steel wall tie for connecting masonry to an in-situ structure, featuring an integral drip for use across a cavity and a 7mm fixing hole. Can be fixed to a range of materials including concrete, steelwork and masonry. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled. Optional insulation retaining clip.

2D detail – plan view
Ancon ST1 Wall Tie -

2D detail – plan view

Stainless steel Type 1 (heavy duty) wall tie for connecting two leaves of a cavity wall with integral water drips. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled. Optional insulation retaining clip.

2D detail – plan view
Ancon Two-Part Tie -

2D detail – plan view

Stainless steel two-part wall tie for connecting the leaves of a cavity wall. One section is built into the blockwork and the other section is fixed as the outer leaf is constructed. CE marked to BS EN 845-1.

Tie length is parametrically controlled. Optional insulation retaining clip.

2D detail – plan view
Staifix HRT4 Wall Tie -

2D detail – plan view

Stainless steel Type 4 (light duty) wall tie for connecting the leaves of a cavity wall. Suitable for housing developments up to 10 metres in height. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled. Optional insulation retaining clip.

2D detail – plan view
Staifix RT2 Wall Tie -

Staifix RT2 Wall Tie

Stainless steel Type 2 (general purpose) wall tie for connecting the leaves of a cavity wall. Suitable for housing and commercial developments. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled. Optional insulation retaining clip.

Staifix RT2 Wall Tie
Ancon SD21 Tie & 21/18 Omega Channel -

2D detail – plan view

Stainless steel, high performance, self-anchoring cast-in channel slot with cavity wall tie. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled. Optional insulation retaining clip.

2D detail – plan view
Ancon SD25 Tie & 25/14 Channel -

2D detail – plan view

Stainless steel channel and tie system for connecting masonry cladding to steel stud framing with high thread screws through rigid insulation board. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled.

2D detail – plan view
Ancon SP21 Wall Tie & 21/18 Omega Channel -

2D detail – plan view

Stainless steel, high performance, self-anchoring cast-in channel slot and shear tie. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled. Optional debonding sleeve.

2D detail – plan view
Ancon PP21 Movement Tie & 21/18 Omega Channel -

2D detail – plan view

Stainless steel, high performance, self-anchoring cast-in channel slot with debonded tie for use at vertical movement joints that abut concrete columns. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled.

2D detail – plan view
Ancon PPB Movement Tie -

2D detail – plan view

Stainless steel debonded wall tie for use at vertical movement joints that abut columns. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled.

2D detail – plan view
Ancon SPB Frame Cramp -

2D detail – plan view

Stainless steel, plain-ended wall tie for connecting masonry to an in-situ structure, featuring a 7mm fixing hole. Can be fixed to a range of materials including concrete, steelwork and masonry. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled. Optional debonding sleeve.

2D detail – plan view
Ancon PPS Movement Tie -

2D detail – plan view

Stainless steel lateral restraint slip tie for use across movement joints in masonry walls. CE marked to BS EN 845-1. Standard tie lengths available.

Tie length is parametrically controlled.

2D detail – plan view
Masonry Support
Ancon MDC

3D Detail

A bespoke stainless steel bracket-angle system to support masonry cladding. Systems can be supplied with a range of components including thermal breaks, shims, closer plates and expanded metal lath. CE marked to BS EN 1090-1.

Standard 3D view shows horizontal angle only. Bracket detail shown in section view. Bracket depth and angle position is parametrically controlled.

3D Detail
Ancon MDC/I

3D detail

A bespoke stainless steel bracket-angle system to support masonry cladding with the support angle at the top of the bracket. Systems can be supplied with a range of components including thermal breaks. CE marked to BS EN 1090-1.

Standard 3D view shows horizontal angle only. Bracket detail shown in section view. Bracket depth and angle position is parametrically controlled.

3D detail
Ancon MDC/R

3D detail

A bespoke stainless steel bracket-angle system to support masonry cladding with a reversed angle welded to the bracket. Systems can be supplied with a range of components including thermal breaks. CE marked to BS EN 1090-1.

Standard 3D view shows horizontal angle only. Bracket detail shown in section view. Bracket depth and angle position is parametrically controlled.

3D detail
AnconOptima

3D detail

AnconOptima is a standard masonry support system, comprising brackets, angles with pre-marked fixing zones and locking wedges. Available in three standard systems to support an unfactored masonry load of up to 10kN, 12kN and 14kN. Optional extras include thermal breaks, shims etc.

Standard 3D view shows horizontal angle only. Bracket detail shown in section view. Bracket depth is parametrically controlled.

3D detail
Masonry Reinforcement
Ancon AMR-X Masonry Reinforcement -

2D detail – plan view

Welded, stainless steel, ladder-type reinforcement used to improve the structural performance of masonry walls by providing additional resistance to lateral loads. Shaped cross wires ensure longitudinal wires are located in the centre of a mortar joint. CE marked to BS EN 845-3. Standard tie lengths available.

Product width and wire diameter are parametrically controlled.

2D detail – plan view
Windposts
Ancon WP1

3D detail

Ancon Windposts span vertically between floors to provide lateral support for panels of masonry. WP1 is a lipped channel section windpost which installs within the cavity leaving the blockwork undisturbed. Supplied complete with end connections and wall ties. Product is CE marked to BS EN 1090-1.

Standard 3D view shows vertical post only. Wall tie details shown in section view. Section size, post length and wall tie length parametrically controlled.

Ancon WP2

3D detail

Ancon Windposts span vertically between floors to provide lateral support for panels of masonry. WP2 is an angle section windpost. One leg of the post is built into the blockwork. Supplied complete with end connections and wall ties. Product is CE marked to BS EN 1090-1.

Standard 3D view shows vertical post only. Wall tie details shown in section view. Section size, post length and wall tie length parametrically controlled. Optional wall tie debonding sleeve.

Ancon WP3

3D detail

Ancon Windposts span vertically between floors to provide lateral support for panels of masonry. WP3 is a channel section windpost which installs within the cavity leaving the blockwork undisturbed. Supplied complete with end connections and wall ties. Product is CE marked to BS EN 1090-1.

Standard 3D view shows vertical post only. Wall tie details shown in section view. Section size, post length and wall tie length parametrically controlled.

Head Restraints
Ancon FHR Head Restraint -

2D detail – section view

The stainless steel FHR connects the top of a masonry wall to the underside of a structural frame. CE marked to BS EN 845-1. Standard sizes available.

Product size is parametrically controlled.

2D detail – section view
Ancon IHR-B Head Restraint -

2D detail – section view

The IHR-B provides the necessary restraint to the top of masonry walls and accommodates vertical movement. Other head options including –C (channel). CE marked to BS EN 845-1. Standard size suits a standard 215mm block.

2D detail – section view
Tension Systems
Ancon 500 Tension System – Disc

3D detail

High performance tension bar system. CE marked to Technical Approval ETA06/0146.

Disc for junctions with multiple tie bars. Disc size is parametrically controlled.

3D detail
Ancon 500 Tension System – Tie Bar

3D detail

High performance tension bar, typically used to restrain roof timbers, canopies, masts and glazing. CE marked to Technical Approval ETA06/0146

Single tie bar. Bar diameter and bar length are parametrically controlled.

3D detail
Shear Load Connectors
Ancon DSD Shear Load Connector

3D detail

High performance, two-part, stainless steel, double-dowel connector used to transfer shear across expansion and contraction joints in concrete. Accommodates longitudinal movement.

Object supplied in 10 standard sizes.

3D detail
Ancon DSDQ Shear Load Connector

3D detail

A high performance, two-part, stainless steel, double-dowel connector used to transfer shear across expansion and contraction joints in concrete. A rectangular box section accommodates lateral and some rotational movement as well as longitudinal movement.

Object supplied in 9 standard sizes.

Ancon ESDQ-L20 Lockable Dowel

3D detail

Stainless steel, two-part, Lockable Dowel for use at a mid-slab temporary movement joint in post-tensioned concrete. It accommodates an initial phase of movement and is then locked with a plate and resin.

1 standard size.

Ancon ESDQ-L20W Lockable Dowel

3D detail

Stainless steel, two-part, Lockable Dowel for use a temporary movement joint in post-tensioned concrete at a wall-to-slab interface. It accommodates an initial phase of movement and is then locked with a plate and resin.

1 standard size.

Ancon HLDQ-L30 Lockable Dowel

3D detail

Heavy duty, stainless steel, two-part, Lockable Dowel for use at a mid-slab temporary movement joint in post-tensioned concrete. It accommodates an initial phase of movement and is then locked with a plate and resin.

1 standard size.

Punching Shear Reinforcement
Ancon Shearfix Punching Shear Reinforcement

3D detail

Double-headed carbon steel studs, welded to flat rails, positioned around a column head/based to provide additional reinforcement against punching shear. Allows flat slab construction.

Ancon EC2-compliant design program available.

Stud diameter, stud length, stud spacing and rail length are parametrically controlled.

3D detail
Reinforcement Continuity Systems
Ancon KSN Anchors -

2D detail

KSN Anchors, in conjunction with BT parallel-threaded reinforcing bars, provide reinforcement continuity at slab-to-wall concrete construction joints.

Object supplied in standard anchor/bar sizes.

2D detail

Latest News

Catch up on the latest developments from Ancon

Architectural Trends in Brickwork

In urban landscapes sometimes dominated by steel and glass, beautifully formed, gravity-defying brick facades can really grab the attention and provide a refreshing, sometimes challenging, contrast to the architectural vernacular.