Lakhta Center, St Petersburg, Russia
The Lakhta Center is a large mixed-use non-residential development featuring the first supertall skyscraper in St. Petersburg, a scientific and educational complex, sports and leisure facilities and an outdoor amphitheatre. Construction of the 87 floor, 462 metre high tower was completed in 2018.
The tower superstructure rests on a 3.6m thick foundation raft. The concrete pour for the raft, which ended on 1st March 2015, was registered by Guinness World Records as the largest ever continuous pour at the time.
The superstructure consists of a cylindrical reinforced concrete core. Overall stability is achieved by means of four sets of outriggers positioned at intermediate levels, connected to the perimeter of the core and to ten external columns. The external columns follow a helicoidal pattern as they progress upwards.
Couplers and headed anchors
Due to exceptional reinforcement volumes, Ancon reinforcing bar couplers and headed anchors were used extensively in the construction of the foundation raft to avoid unnecessary overlapping of bars and minimise congestion.
Nearly 80,000 Ancon CXL32 reinforcing bar couplers were used for the splicing of 32mm diameter horizontal reinforcing bars, which were arranged in 15 layers in orthogonal directions over the depth of the raft.
Over 45,000 Ancon CXL32HA and 6,000 Ancon MBT ETHA32 headed anchors were used at the extremities of the reinforcement at the edges of the raft to replace traditional hooked ends which would otherwise have exacerbated reinforcement congestion.
CXL couplers are compact and produce a full strength joint. The end of each bar is enlarged by a special cold forging process, increasing the core diameter of the bar to ensure that the joint is stronger than the bar. Parallel metric threads are cut onto the enlarged ends, which are systematically proof-tested to a force equal to the characteristic yield strength of the bar.
MBT ETHA headed anchors are designed to provide dead-end embedment: a bearing plate welded to the MBT coupler body transfers the full tension load of the bar to the surrounding concrete. The bar end is supported within the coupler body by two serrated saddles and as special lockshear bolts are tightened, the conical ends of the bolts embed themselves into the bar while the serrated saddles bite into both the bar and the shell of the coupler, thus creating a full strength joint.
Vertical reinforcement splicing
Ancon CXL Type B splices were also used to minimise congestion in the multi-layered vertical reinforcement of the central core: CXL40 and CXL36 couplers for the lower portion of the core, and CXL32 for the upper portion.
In this method, one of the bars to be joined is threaded for a full coupler length which allows the coupler to be rotated from this position to the second fixed bar to make the splice. These Type B slices are ideal where it is difficult to rotate the reinforcing bars and was a significant advantage in this instance due to the length and weight of the reinforcement.
Continuity of reinforcement between floor slabs and the central core was achieved by means of two Ancon systems; Ancon KSN threaded anchors and Ancon CXL Coupler Box.
First-phase internally threaded anchors and couplers were supplied fixed to timber carriers or steel casings respectively, which enabled rapid and accurate installation of multiple items to the core reinforcement. After slip-forming of the core, these continuity systems provide an indented shear key in the concrete face to increase design capacity of the joint. Continuation rebars, featuring CXL parallel threads, were inserted in the anchors and couplers to complete the connection and then lapped with the slab’s main reinforcement.
The principal advantage of these connection methods was a significant increase in the speed of installation over rebend continuity systems and individually-fixed items.
The outriggers are 7.1m deep beams, combining structural steelwork lattice girders with reinforced concrete. Connections between the outriggers and the external columns used 25mm diameter Ancon Shearfix CXL studs.
Reinforced concrete connections between the outriggers and the central core used a combination of 25mm diameter Ancon Shearfix CXL studs, and 32mm anchor bars fitted with CXL32 couplers at one end and welded anchor plates at the other end.
Shearfix CXL studs feature an anchor head formed at the end of a length of reinforcing bar using a special hot-forging and quenching process. The other extremity of the stud is fitted with a CXL coupler, enabling connection with a threaded continuation bar to be cast in the second phase concrete.
The avoidance of lapped reinforcement in the foundation raft and central core minimised rebar congestion and ensured that wet concrete was able to flow effectively when poured, avoiding segregation and structural defects.
The use of Ancon KSN headed anchors, CXL Coupler Box and Shearfix CXL studs for the connection of slabs and outriggers to the central core and external columns meant that plain-faced formwork could be adopted throughout.
Overall, these solutions resulted in an accelerated speed of construction and a high level of quality in the pouring of concrete, ensuring that construction could keep pace with a demanding site programme.
The use of Ancon Reinforcing Bar Couplers can simplify the design and construction of reinforced concrete and reduce the amount of reinforcement required.
Leviat manufactures six Ancon products which provide continuity of reinforcement at slab-to-wall construction joints in concrete.
Our offices will close on Thursday 23rd December and reopen on 4th January 2022.
The latest innovative product developments from each of Leviat's established and trusted connecting, fixing, and anchoring brands will be showcased on our stand at London Build 2021.